How

How To Remove Broan Bathroom Fan Cover?

How To Remove Broan Bathroom Fan Cover?

There are a few basic steps involved in the removal of a broan bathroom fan cover. You simply need to remove the clips and screws holding the cover. This way, the fan cover easily slides out.

Fan covers get dirty after a while as a result of the continuous exposure to air featuring dust. That said, it is advisable to frequently clean your fan cover. Otherwise, when lots of dust accommodates on the fan cover, the fan’s performance will eventually get affected.

A fan covered in dust will not function properly. And if your bathroom exhaust fan is filled and chocked with dust, the excess moisture will not be able to escape, which will eventually result in mildew and mold.

When it comes to a broan bathroom fan cover, instead of having it replaced with a new cover, you can simply remove it, get it clean, and then return it back to its original position. This goes a long way in saving you from the expense of having to get a new bathroom fan cover.

If your bathroom fan cover is filled with dust, it could adversely impact the performance of the fan, which will lead to the eventual failure of your ventilation process. According to experts, a bathroom fan cover should be cleaned after every six months.

Below are the steps involved in removing a broan bathroom fan cover.

Steps to remove a broan bathroom fan cover

Step 1: Switch off the electricity switch

Anytime you are handling or working on an electric gadget or device, you need to begin by cutting off its electric supply. This goes a long way in saving you from unforeseen electric hazards.

Before you start the process of removing your broan fan cover, make sure that you cut off the bathroom’s main electricity supply. If things get dark, you can use a flashlight or torch to help light things up.

Also, get a ladder or a steady stool for you to stand on. This allows you to easily reach your bathroom’s ceiling.

Step 2: Removing the fan cover

Check for any clips and/or screws that have been used to attach the fan cover to the main exhaust fan unit. Keep in mind that the type of attachment depends on the broan fan model that you have installed in your bathroom.

Broan bathroom fan covers do not normally feature clips. This, however, does not mean that you should pull down the cover without having double-checked for clips and screws. When it is time for you to pull down the fan cover, do so in a gentle and careful way. Pulling the cover using a lot of force or in a harsh manner might lead to breakage of the cover; you don’t want this to happen.

In case of any screws, carefully unloosen them and place them put them in a safe place as you’ll still need them later when returning the fan cover back to its original spot.

Once you have successfully removed the cover, you can proceed to do the work for which you removed the fan cover. Perhaps you were looking to repair your broan fan, replace your fan cover, or simply wanted to clean your fan cover.

How to clean your Broan bathroom fan cover

Here is a detailed description on how to clean your broan bathroom fan cover.

  • Clean the cover using soapy water

Cleaning the vent cover is quite simple. Fill up your sink with warm water and then add a few drops of dish soaps to the water. Dip the fan cover into the warm soapy water and leave it to soak for a while before taking it out of the water and cleaning it using a clean cloth or dry towel.

Carefully scrub the cover to get rid of all dust, dirt, and mold. After cleaning is done, place tit on the floor and leave it to air dry.

  • Remove dust from the exhaust fan using a  vacuum

Before beginning any clean up job on the exhaust fan, you have to first unplug the two-prong switch that supplies power to the fan. For extra care and precaution, switch off the bathroom’s power supply from the circuit breaker.

Once you are sure that the fan’s electric supply has been cut off, you can proceed to clean the fan. You can use a vacuum to get rid of the accumulated dust. You should, however, use a scrub brush to remove the dust and dirt from the motor pieces.

  • Get rid of grime using a wet cloth

After getting rid of the dry dust, you are ready to move to the next step. You might have noticed that your exhaust fan still looks dirty even after removing the dust. What is left behind is wet dirt and dust; grime. Use a wet towel or cloth to wipe down the parts of the fan that still look dirty.

Do not be scared of dismantling the fan even further to give it a deep clean. Unscrew any visible screws and remove the motor from the casing of the fan to give it a nice clean job.

  • Reassemble the Broan exhaust fan

After cleaning your both your Broan fan as well as fan cover, it is time to reassemble your fan. If you detached the motor from its casing, put it back to its original position and secure it with the help of screws. Plug in the fan’s switch to observe if and how the fan is working. 

After confirming that your fan is properly working, turn off the switch once again to return the fan cover. Put the cover back where it was by inserting the wires back to their previous slots and then gently and carefully push the fan cover back in place.

Do you need an electrician to replace a bathroom fan?

Installing a bathroom fan in a room that doesn’t currently have one is a significant job because you’ll need to have an experienced contractor fit the wiring and run air ducts to vent the air out of the room through the wall or roof. You’ll need to have an electrician request the permit and install the fan for you.

Is it bad to leave your bathroom fan on?

Experts say bathroom fans can become overheated when clogged by lint and dust when left on too long or because of simple failure. The heat can ignite the lint, causing the fire. Run the fan for only short periods, and never leave it on overnight or while no one is home.

How often should you clean the bathroom fan?

Prevent dust buildup on both the exhaust fan cover and motor by cleaning it once or twice each year. This straightforward bathroom cleaning task takes just 20 minutes to complete, plus you only need a few tools to get the job done.

How To Remove Broan Bathroom Fan Cover – Related Questions

Why does my bathroom fan not turn off?

One common issue with bathroom exhaust fans running non-stop is wiring issues. A bathroom fan that is running non-stop is usually not caused by the circuitry or wiring of the fan itself. If the circuitry or wiring of the fan were malfunctioning, it is more likely that the fan would not turn on at all.

Can I replace the bathroom extractor fan myself?

If you only need to replace an extractor fan, swapping old for new, you should be able to use the existing wiring, ducting, and exhaust venting. It’s a straightforward DIY job that only requires basic disassembly and securing screws. Also, check the dimensions of your new fan line up with the existing holes.

What causes a bathroom fan to stop working?

A fan is essentially an electric motor with a propeller or drum-like blades. When bath and range-hood fans stop working, the problem is usually one of two things: the fan isn’t receiving power or the motor has burned out. If it’s dead to the world, check the circuit breaker that serves the fan.

How do you clean an exhaust fan without removing it?

Prepare a mix of water and soap or you can also add a mixture of 1/4 ammonia, 2 tbsp baking soda, and 1 cup full of warm water. Put on the rubber gloves and, using the above mixture and cotton cloth, scrub the exhaust fan blades and then the rest of the body.

How do you remove a vent cover?

The task of removing a vent cover is straightforward, and any homeowner should be able to do it. Most of the time, the vent cover is held in place on the floor with two screws, one on each end. Use a screwdriver to twist the screws counter-clockwise and remove them, and just lift the vent cover up to remove it.

How much does it cost to replace a bathroom exhaust fan?

Cost to replace a bathroom fan

Bathroom fan replacement costs $150 to $550 total on average. Homeowners should replace bathroom vent fans every 10 years. Fan and vent installers charge $50 to $100 per hour for labor, and replacement takes 2 to 3 hours. Wiring a new switch costs $100 to $250 more.

Who can fix a bathroom extractor fan?

If your extractor fan continues to be faulty after giving it a clean, you should get a qualified electrician in to fix it. Why is my bathroom extractor fan not working? Due to the amount of hot air that the fan filters out, the blades can collect dust and dirt resulting in it becoming faulty.

Does a bathroom fan help with smell?

The primary purpose of having an exhaust fan is to remove the moisture out of the bathroom. These fans help to control and eliminate bathroom odors. Additionally, they add to the safety of the home and its residents by reducing fumes from cleaning agents that could potentially cause health-related issues.

Does a bathroom fan use a lot of electricity?

Basic fan-only ventilation units can use as little as about 6 watts, for highly efficient models, while many standard units often use around 60 watts or more. In general, electricity usage is related to airflow, measured in cubic feet per minute (cfm) and the fan’s energy efficiency.

How long should a bathroom fan last?

Routine cleaning will help extend the life of your exhaust fans, but they won’t last forever. The average life of a bathroom exhaust fan is about ten years, and kitchen hood fans tend to hang in there a little longer at around 15 years.

Can you replace the bathroom fan with a light?

How
Bathroom Fan with Light | Pinterest

They remove moisture that can lead to wall damage and mold. Replacing a bathroom vent fan/light combo is an intermediate-level project you can do on your own in just two to four hours. When taking on this DIY task, be sure to equip yourself with the proper safety gear. Remove the old fan mechanism.

Should I replace my bathroom fan?

Bathroom vent fans should be replaced if the fan is over 10 years old, won’t turn or is slow to turn, is noisy caused by a broken blade or excessive vibration. Bathroom fans will often start turning slowly or become very noisy before it completely quits. These are signs that your fan needs to be cleaned.

Can I vent a bathroom fan to the attic?

The Code of Bathroom Exhaust Fans

Air shall not be exhausted into an attic (except whole-house ventilation), soffit, ridge vent, or crawl space.

Is it hard to replace a bathroom exhaust fan?

It’s easiest to install a bathroom vent fan if you’re replacing an existing fan. You can use the existing switch, wires, and ductwork. Also, it helps to get a fan that’s the same size as your existing fan so you won’t have to adjust the size of the ceiling hole.

What is the code for venting a bathroom fan?

Section 1203.4. 2.1 of California’s building code requires all bathrooms with a bathtub, shower, spa or similar fixtures to be ventilated by an exhaust fan. The fan must be Energy Star-compliant and vented to the outside.

What can I use if I don’t have a bathroom fan?

If your bathroom doesn’t have a fan, take advantage of the door and window(s) to let out steam. Whenever weather permits, open the window during your shower or bath and leave the window open for at least 15 minutes after you exit.

Can you use wd40 on a bathroom fan?

WD-40 is a good lubricant for exhaust fans because it will also help break up any remaining dirt, dust, and grease, although you can also use other lubricants, such as silicone spray, to lubricate an exhaust fan. Use your hand to spin the fan blades a few times, and clean up any lubricant that drips down the motor.

How loud should a bathroom fan be?

Bathroom fan sound levels are measured in sones: 4.0 sones are the sound of standard television operation; 3.0 sones is typical office noise; 1.0 sones is the sound of a refrigerator, and 0.5 sones are the sound of rustling leaves. For quiet bathroom ventilation, the fan should be rated at 1.0 sones or less.

Why does my bathroom fan turn on automatically?

When you enter your bathroom, the window is open and there’s no one in the house, yet the fan turns on. It has become an annoyance for most people when they’re relaxing after a long day of work.

When this happens, it means that something in the bathroom is letting out too much heat so your cooling system thinks it needs to switch on to cool down the room. This may mean either turning on your AC or turning on your exhaust fan at longer intervals than usual.

However, if you find yourself constantly having to turn off the fan because of this reason then there’s a good chance that you have an old fan or blocked exhaust that requires replacement. There are two ways to test if your fan is working correctly: place a piece of toilet paper in front of the fan, then turn it on. If the paper sticks to the exterior of your fan then you have a suction problem that means you need to replace the old fan with a newer, more energy-efficient one. Otherwise, if the paper falls right off, it’s blocked exhaust and needs cleaning out.

Another way would be going outside and feeling how cool your exhaust is against your hand. If it’s hot or warm then you have a blockage somewhere in your exhaust system whether it is caused by dirt build up over time or grease from cooking blocking up an opening. In this case, leave everything as is but set aside some time for later on where you can clear away any blockage from your system so that you don’t have to turn your fan on more than you need.

Note: This problem is most commonly caused by an old fan or a blocked exhaust. You can test the fan’s suction by placing a piece of toilet paper against the exterior of the fan; if it does not hold, then you need to replace the old fan or solve the blocked exhaust.

Read More On: How to Convert Briggs and Stratton CC Instantly into Horsepower?